Reference notes for moving heat from one pipe stream to another without mixing them: feed-water heaters, coolers,
economizers, reheaters.
What it does
The exchanger has two sides, A and B. Each side is its own pipe path through the block. The fluids never mix:
only heat crosses, from the hotter side to the colder. Either side may hold water, steam, air or exhaust gas, and steam
may condense or water boil inside it.
Small inside. Each side holds 1 B per block. Water passes through it; it is not a tank and not a boiler drum.
Heat moves by area, not volume. One block passes 12.5 W per kelvin of difference between the sides. Four
blocks in a 2 × 2 slice pass 50 W/K.
Stacking. Blocks stacked 2 × 2 across and up to 8 long, all facing the same way, work as one exchanger: 2 × 2 × 2
is 100 W/K, 2 × 2 × 4 is 200 W/K, 2 × 2 × 8 is 400 W/K. Any other shape (a lone block, a 1 × 2, a 3 × 3) works as
separate blocks of 12.5 W/K each. Jade shows which one you have.
Ports and flow directions
Both sides have a port on each end face (the faces along the way it was placed):
A at the centre of the end face.
Bup high on the end face (in a stack, on the top row too; take steam off a stack's top row).
Counterflow is the point of the device: the two streams run in opposite directions.
A goes in at the back end and out at the front.
B goes in at the front end and out at the back.
The ports at the two ends look the same, so nothing stops you piping it the wrong way round. Walk along it before you
open the valves: the hot stream's inlet and the cold stream's outlet should be at the same end.
Block layout, seen from above (front to the east):
back (west) front (east)
A in ----> [ HX ][ HX ][ HX ][ HX ] ----> A out (hot stream)
B out <---- [ HX ][ HX ][ HX ][ HX ] <---- B in (cold stream)
(2 x 2 x 4: two more rows on top)
Both streams must flow. A side with no way out fills, warms up to the other side's temperature, and then takes almost
nothing.
What to expect
From GameTests (EA 26.x, 1 B a side):
Build
Hot side
Cold side
Duty
Notes
Feed heater, one block (12.5 W/K)
bleed steam, 2.4 bar (126 °C), condensate out through a trap
feed water, 20 °C, ~5 g/s
1.0 kW
feed out ~69 °C
Feed heater, 2 × 2 × 2 (100 W/K)
the same steam
feed water, 20 °C, ~10 g/s
3.9 kW
feed out ~113 °C, 12 K under the steam
Cooler, 2 × 2 × 4 (200 W/K), counterflow
hot water 90 °C, 23 g/s
cooling water 20 °C, 23 g/s
4.3 kW
hot out ~45 °C, cooling out ~65 °C
The same, both streams in at one end
3.3 kW
a quarter less; hot out 56 °C, cooling out 54 °C
The same, cooling outlet left off
0.4 kW, falling
its standing water has warmed to ~85 °C
Steam raiser 2 × 2 × 2 on a gas turbine's exhaust
exhaust 500 °C
water boiling at 14 bar
10.9 kW
92 % of what the exhaust could give
Reheater 2 × 2 × 4
live steam 18 bar, condensing
crossover steam 2.4 bar, 44 g/s
6.5 kW
crossover 126 → 198 °C
A good counterflow exchanger can send the cold stream out hotter than the hot stream leaves. In the cooler above the
cooling water leaves at 65 °C while the hot water leaves at 45 °C. If your cold outlet is colder than your hot outlet,
the streams are probably running the same way.
Rules of thumb:
W/K of the exchanger ÷ (flow in kg/s × 4186) for water is the NTU. Under about 1, more exchanger pays
well. Over about 3, more exchanger adds little.
A lone block is for small streams (a few g/s of water). For gas, or anything over about 10 g/s of water, build a
2 × 2 stack.
It is narrow inside: a stream loses a little pressure crossing it, more through a lone block than a stack. A
reheater's 44 g/s of crossover steam needs about 5 kPa across a 2 × 2 × 4; a pump or a boiler covers that easily.
Builds
Combined cycle: a gas turbine's exhaust raises steam
This is what the exchanger is for. A gas turbine throws away about 70 % of its fuel as exhaust at 500 °C. Two 2 × 2 × 2
exchangers turn part of that into steam for a steam turbine.
Exhaust path (side A): gas turbine exhaust into the raiser's A at the back, out at its front, through a pipe
into the economizer's A at the back, and out of its front to the air.
Water path (side B), the other way: the feed pump (about 16 bar) into the economizer's B at the front
(where the exhaust leaves, coolest), out at its back, through a throttle valve, into the raiser's B at its front.
Steam: off the raiser's B at the back, top row, into a separator tank, and from its top to a steam turbine
(the test used an HP shaft turbine and generator).
Two controls:
* Level: the raiser's water side holds only 8 B, about a minute of steaming. The feed valve must follow its level:
open more as it drops, less as it rises.
* Pressure: the steam turbine's throttle holds the raiser at about 14 bar. Wide open, the pressure falls and each
kg of steam does less work.
Measured, the turbine burning 26.1 kW of fuel for 7.5 kW of shaft power (28.8 %):
The raiser took 10.9 kW and the economizer 3.8 kW from 18.6 kW of exhaust. The exhaust leaves at about 115 °C.
The water went 20 → about 180 °C in the economizer, and boiled in the raiser at 14 bar: 4.7 g/s of steam.
The steam turbine made 1.7 kW. Together: 9.2 kW from the same fuel, 35 %, +22 % over the gas turbine alone.
Condensate reheat in a small plant
For a boiler and a 230V Steam Turbine with a Steam Condenser: the condenser hands back its water at about
35 °C, and the boiler spends fuel heating it again. Heat it with the furnace's flue instead.
Water (side A): the condenser's pump outlet into the exchanger's A at the back, out of its front into the
boiler's feed flange. A 2 × 2 × 1 (50 W/K) is plenty.
Flue (side B): a pipe from the furnace's flue flange into B at the front, out at the back to a chimney or the
air.
The turbine's throttle holds the boiler pressure (8 bar in the test).
Measured, two such plants side by side, each boiler fired at the same 12 kW (a furnace's share; its flue carries about
5.3 kW over the ambient at 300 °C):
The condensate went 34 → 167 °C. The exchanger took 3.0 kW from the flue.
The plant without it made 2.19 kW; with it, 2.70 kW: +23 % from the same fuel.
The feed can't get hotter than the boiler's boiling point (170 °C at 8 bar). A bigger exchanger buys nothing more.
Common mistakes
Both streams in at the same end. It takes about a quarter less, and the cold stream can never leave hotter than
the hot one.
A side with no outlet. Its water warms to the other side's temperature and the duty falls towards zero.
A lone block on a big stream, or the wrong shape. Only exact 2 × 2 × 1 to 2 × 2 × 8 boxes join up; Jade says "one
block, a quarter slice" when they haven't.
Exchangers built before the resize held 113 B a side. They keep 1 B and vent the rest on loading (Jade: "Resized").