One violet cable, any number of devices. It works in voxel blocks only.
The bus
A run of Field Bus Cable, laid from a Field Bus Cable Kit, and every device whose bus pin a run reaches form one bus. The bus carries two things:
16 colour channels. Levels from 0 to 1, a share of 5 V, numbered like the dyes: 0 white to 15 black. A channel
holds its level. When two writers disagree, the last change wins, and when a writer stops, the others' levels
come back. A channel nobody writes falls to 0.
Packets sent to an address: [target][source][type][payload].
target
meaning
0
everyone (broadcast)
1 to 16
colour channel 0 to 15
17 to 255
one device, by the address set in its screen
type
name
payload
what it does
1
signal
a level 0 to 1
to 1–16: sets that channel
2
press
button index
a button was pressed (sent to everyone)
3
power
a level 0 to 1
a lamp's brightness, a button's light
4
write
register, value
sets a device register
5
read
register
asks for a register
6
reply
register, value
the answer, sent back to whoever asked
7
fault
code
a device reports a fault (sent to everyone)
8
arrive
sensor index
a Floor Sensor saw the car stop (sent to everyone)
9
data
index, up to 64 bytes
between computers: the index and bytes are the program's own; devices ignore it
Packets sent in one tick arrive at the next, sorted by sender. A bus carries 64 packets a tick; more are dropped,
and Jade on the cable counts them. Jade on the cable also lists the device addresses on the bus. Two devices with
one address are flagged as DUPLICATE.
The devices
Bus I/O Module: nine signal terminals onto colour channels, in or out. Its pins wear their channel's dye.
Addressable Button: a click sends press from its address. Its lamp lights when it is sent power. Sneak and
click it to set its address.
Addressable Light: as bright as the last power sent to it.
Floor Sensor: on a landing beside the shaft. Register 0 is 1 while the car stands level with its floor, and it
sends arrive when the car stops there.
Linear Servo Drive: an addressed device. Click it to set its address.
register
drive
0
target height, blocks above its foot (write)
1
position (read)
2
speed limit, m/s, 0 for none (write)
3
state: 0 idle, 1 in position, 2 moving, 3 fault
4
load, kg
Fault codes: 1 something in the way, 2 too hot, 3 rail missing or broken, 4 line voltage too high.
Building the elevator
The drive goes at the foot of the shaft, with a Servo Rail mast of 2 to 32 blocks on top and 230 V on
its back. The cabin is 3 × 3 × 3. It rides over the three rows of blocks in front of the drive, open at the
front, so keep that 3 × 3 shaft clear up to 3 blocks above the top stop.
The pins are all on the floor edges of the drive's flanks, three per flank. Left and right are as you face
that flank:
* Left flank (seen from the car side): in-position, setpoint (middle), position.
* Right flank: fault, enable (middle), and the violet bus pin.
Cable laid from a kit can end at any of the three: click the pin you want.
Without a computer: a signal on the setpoint is a share of the travel (0 V the bottom, 5 V the top), rounded
to the nearest block. A connected setpoint overrides the bus.
The car's panel is the board inside the back wall: 12 slots, 3 across and 4 down. Hold an Addressable Button or
Light and click a slot to put it in. Sneak and click with an empty hand to take it back. In the drive's screen,
"Car panel from" sets the first slot's address. The others follow left to right, top to bottom. The panel
rides on the drive's own bus (the travelling cable), so it needs no cable.
On the landings: an Addressable Button by each door, on the bus run up the shaft. A Floor Sensor at each
landing, if you want the program to find the floors by itself.
A program on the bus does the rest. It listens for press, lights the buttons whose calls it has taken, and writes
the drive's target. It reads register 3 until the car is in position, then serves the next call. A
Computer with the Elevator floppy is that program, ready made: set the addresses and floor heights
at the top of its a:/main.janet.