Day 24 — Stability at the fencepost: 22%
The stillness crept past the north culvert this morning. Twenty-two percent at the post now, and no spare steel coming up from the valley. That made it a bad morning for my good pick to hit its fourth life. Every time I took it to the old anvil the smith's price climbed, until today the iron simply refused with Too expensive! Steel does not get tired, Kid. That ratchet is a smith's superstition hammered into the block, and I was not about to lose a good pick to it.
So I built the Electrical Anvil, a proper workshop desk with a vise, an arc welder, and a lamp over the plate. It takes tougher metal than mild iron, so plan on two shop machines first: the Macerator and the Plate Machine. Grind raw tungsten in the Macerator for tungsten dust, then mix two iron dust, one coal dust, and one tungsten dust by hand to get two Alloy Dust. Smelt that into Alloy Ingots and roll them through the Plate Machine into Alloy Plates. Four Alloy Plates around a Copper Cable make an Advanced Machine Block. All the plates for today's work come off that same Plate Machine.
To frame the desk itself, set that Advanced Machine Block under a plain vanilla anvil, flank it with two iron plates, put Copper Cables in the top corners, and stand it on two iron ingots at the bottom corners.
The catch is the welder. It connects on its back plate and wants 400 V, stepped up from the steam plant's 48 V bus. Push it past 520 V and it burns. Electrically it is a 32 Ω load, which means five kilowatts at 400 V and less as the line sags, falling with the square of the voltage. Five kilowatts is more than my whole steam plant makes.
The first time I struck an arc straight off the plant, the house lights went brown, the turbine moaned, and the desk quit after a second with Supply too weak. It held off a second, tried again, browned the shed out again, and quit again. All afternoon.
The welder is not greedy all the time, though. It works in bursts of 20 kJ, roughly four seconds of arc, two bursts for each unit of repair material to restore a quarter of the tool. Between bursts it rests at least three seconds, and between tools it pulls nothing at all. Before each burst it waits for 380 V on the line, or 372 V once the voltage has sat steady for two seconds. If the line drops under 360 V, it pauses with Supply too weak, keeps every bit of its progress, waits a second, and watches the voltage climb again.
My plant makes plenty of energy over a minute. It just cannot deliver it fast enough in those four seconds. That is a peak load, and there are two ways to meet one: a generator sized for the peak, or a store that fills slowly and empties fast.
A full station bus would shrug this off. Pity the Regional Grid is a museum piece now.
So: a store. A battery will not do. Batteries are built for a steady trickle and wear fast when you yank kilowatts out of them. What you want is a capacitor, a jar that fills while the desk rests and dumps its charge in a rush when the arc strikes. I tried a row of the smaller wall Power Capacitors first. Even packed with nine Dielectrics for a 432 V rating, a capacitor only hands the desk the energy sitting between 400 V and 360 V. That is less than a fifth of what it holds, roughly 1.9 kJ apiece. One 20 kJ burst wanted eleven of them bolted to the wall.
So I built a real Capacitor Bank: six fat cans on a steel rack. That calls for one more shop machine, the Compressor, which squeezes one sand into four Dielectric. Six Dielectric, two copper plates, and a redstone block build one Capacitor Cell. Six Cells, two iron plates, and a Copper Cable make the bank. Count it out before you start: thirty-six Dielectric, six redstone blocks, twelve copper plates, two iron plates, and a Copper Cable.
The bank is 1.44 F and rated 500 V. Drive it above 650 V, or cook it more than 75 K over room air through its 0.1 Ω internal resistance, and it blows. If you do scorch one, a Dielectric patches it back up. Wire the bank's plus to the desk's 400 V line and its minus to a Ground Cable. At 400 V it holds 115 kJ, of which 21.9 kJ sits above 360 V. One full bank carries one 20 kJ burst on its own and finishes near 364 V.
Do not mistake it for a battery, mind. It leaks through roughly 1.25 kΩ inside, about 128 W at 400 V. Leave it disconnected for an hour and two percent is left; by morning it is flat. Keep the plant tied in while you work. It is for the punch, not the pantry. The sums are in sizing.
Do not bolt an empty bank straight to a stiff 400 V line, either. I did, once. An empty capacitor is a dead short until it fills, and the high-voltage cable went cherry red and burnt clean through before my hand reached the lever.
Put a Large Rheostat in series between your 400 V supply and the bank. Load it with 23 Coal Dust to set its top value at 82 Ω. Here is the trap that will still burn your cable if you miss it: a Large Rheostat scales with its control signal, and with no signal it sits near 0.8 Ω, barely more than bare wire. Wire the control signal first and set it high so the rheostat starts at the full 82 Ω, never straight onto the line.
Let the bank climb through 82 Ω from empty. Because of that 128 W leak, 82 Ω alone stalls the bank near 375 V, short of the 380 V start. Once the bank passes 300 V, dial the signal down to roughly 25 Ω. The bank rises to around 392 V, clears the desk's threshold, and carries the arc while the rheostat takes the sting out of the recharge. If a burst dips under 360 V before it finishes, the desk pauses cleanly, holds its progress, and picks right back up once the bank climbs.
At the bench itself, lay the worn tool in the left slot and its repair material in the right. A plain unenchanted copy of the tool works in the right slot as well. Enchanted books and enchanted gear are turned away there. If something is missing or wrong, the bench tells you plainly: Put a tool on the bench, Needs its repair material, or This can't be mended here. Once it has power and stock, watch it step through Waiting for 380V, Welding, Between bursts: waiting for 380V, and finally Repaired.
It spends no experience at all. Better yet, every repair step knocks the old anvil penalty down a notch, from 31 to 15, 7, 3, 1, and 0, stopping only at the floor set by the enchantments on the tool. It never raises the cost. The screen tracks your material credit, shows the current anvil cost beside the lowest it can reach, and reminds you no XP is needed. If you want a name cut into the head, type it and press Enter. Engraving costs 2 kJ.
The pick is whole again, its old name fresh on the steel. The house lights did not even flicker, and the quiet outside the fencepost can wait another day.
Previous: The Real Steam Plant: The Day the Valve Sang · Next: none yet