Reference notes for The Real Steam Plant. Kept short so you can read them while a pipe is already whistling.
The boiling-point table
In a closed boiler holding both water and steam, pressure and boiling temperature are locked together. Water cannot reach a pressure until it reaches that boiling point, and if nothing takes steam out, pressure climbs until it matches the fire. Jade percentages below are Jade's pressure efficiency, not thermodynamic efficiency; see thermodynamic efficiency.
Absolute Pressure
Boiling Temp, °C
Plant Milestone
0.04 bar
~29 °C
Condenser vacuum at part load; near air temperature, ~201% on Jade.
0.1 bar
46 °C
Condenser vacuum at full rated load.
1 bar
100 °C
Boiling begins; boiler starts producing steam.
2 bar
120 °C
Where an unregulated turbine collapses the boiler; Jade 29% to open air.
5 bar
152 °C
Floor for the "Under Pressure" advancement: loaded under 5 bar for 30 s triggers it.
48V Steam Turbine rated inlet. Jade 100% to open air.
15 bar
198 °C
230V Submersible Pump shut-off and condenser pump rating. Jade 119% to open air.
18 bar
~207 °C
Condenser return pump shut-off.
20 bar
212 °C
Iron Pipe working limit and HP Steam Turbine operating pressure.
25 bar
224 °C
Iron Pipe burst and 48V Steam Turbine casing burst. Above 25 bar, the turbine explodes.
60 bar
~276 °C
HP Steam Turbine casing burst.
100 bar
311 °C
Alloy Pipe working limit. Bursts at 300 bar.
350 bar
—
Boiler shell burst. Pipes and turbines fail long before this.
The furnace-regulator trap: With no electrical load, the turbine governor shuts its valve and boiler water climbs straight toward your furnace set point.
200 °C -> 15.5 bar
210 °C -> 19 bar
224 °C -> 25 bar, bursting iron pipe and the 48V turbine
250 °C -> 40 bar
260 °C -> 47 bar
Capping furnaces at ~200 °C stops the boiler passing ~15.5 bar, but starves output at 10 bar down to ~7% under load. Running hotter at 230–250 °C moves real heat, provided you fit a Pipe Safety Valve.
Thermodynamic efficiency
Jade's pressure efficiency measures work per gram of steam compared to a 10 bar turbine venting to open air. It is not fuel-to-watts efficiency.
Venting to open air at 10 bar: Uses 3.5 g of steam per kW-second, about 52 mB/s of water per kW. A venting plant drinks water fast: 6 buckets vanish in about 10 minutes.
With a condenser: Exhaust drops to 0.1 bar at 46 °C under full rated load, giving ~19% ideal heat-to-work. At part load the condenser sits nearer air temperature, around 0.04 bar, reading ~201% on Jade and ~21% ideal heat-to-work. After furnace losses, real coal-to-watts runs around 14% — 793 W measured from 5.8 kW of fire.
Inlet Pressure
Boiling Temp, °C
Jade Pressure Eff., Open Air
Notes
2 bar
120 °C
29%
Unregulated collapse pressure.
4 bar
~144 °C
~60%
Still below the 5 bar advancement floor.
10 bar
180 °C
100%
Rated 48V inlet; ~201% on Jade condensing at 0.04 bar.
15 bar
198 °C
119%
Upper edge before 230V pump shut-off.
The three-part control rule
Sliders do nothing without a regulator item. Both furnaces and turbines have a regulator slot. Without a regulator item in the slot, a furnace ignores its temperature set point and a turbine acts as a plain throttle, letting the boiler collapse to ~2 bar.
The turbine regulator holds the pressure floor. Put an Analogic Regulator — crafted from 2 redstone, a Cheap Chip, and an iron ingot — in the turbine's regulator slot. Set "Hold the inlet at: X bar", adjustable from 1 to 25 bar in 0.5 bar steps, default 10 bar. The valve stays shut until inlet pressure reaches the set point, then passes steam, giving 700–800 W at 10 bar in testing. Do not set the target higher than your furnace temperature can boil, or the valve never opens.
The safety valve caps the pressure ceiling. Furnace regulators set to 230–250 °C give strong heat transfer under load, but will burst an unloaded plant without relief. Fit a Pipe Safety Valve set to 15 bar on the steam pipe to bleed excess pressure safely whenever load drops. Set lower, it vents steadily at idle, costing coal and water: the furnace regulators hold the furnaces' temperature, not the boiler's, and nothing throttles the fires for you. If it still vents at 15 bar, turn the furnaces down while idle, or control them from a Thermal Probe on the boiler through a Signal Processor.
Firing the boiler
Stone Heat Furnace: 1 kW base plus 500 W per Combustion Chamber, up to 4 chambers for 3 kW. Heat leaves from its back only, so place backs flush against the boiler's back or flanks. Fails at 800 °C; repair with 1 Combustion Chamber. See the early heat notes.
Fuel Burners: Later-tier liquid-fuel furnaces rated at 2 kW, 5 kW, and 10 kW. Fail at 800 °C; repair with 1 Combustion Chamber.
Electric Heaters: Never run an electric heater to drive a steam turbine — the round trip wastes over 80% of your power. Use them only for surplus power on process heat.
Repairs: Boiler and turbine water damage take a Copper Thermal Cable. Furnaces take a Combustion Chamber. None of them ever take a Machine Block.
Plumbing and hardware
Connections: Touching blocks connect directly — furnace backs to boiler flanks or back, boiler bottom onto a turbine below, condenser onto a turbine's right side. Cables and pipes are laid manually.
Laying pipes: Craft an Iron Pipe Kit from 2 EA iron plates per block; plates must come from the Plate Machine, not hammering. Click a port to start, click block faces for waypoints, and click a port or existing pipe to finish. Click the last waypoint again to cap the pipe there. Sneak-click undoes. Do not end a pipe on the port it started from, and a port that already has a pipe takes no second one. Pipe and cable kits work the same way, and the action bar previews each click.
Pipe limits: Iron Pipe works to 20 bar and bursts at 25 bar. Alloy Pipe works to 100 bar and bursts at 300 bar.
Submersible Pumps: Stand the pump in a water source block. Pipe connects to the top, power to the flanks, and speed signal to the front. Flow drops linearly to zero at shut-off:
48V Submersible Pump: 100 W, 181 mB/s max, shuts off at 6 bar. Too weak to feed a 10 bar boiler directly, but feeds a near-vacuum condenser makeup port easily.
230V Submersible Pump: 400 W, ~725 mB/s max, shuts off at 15 bar. Later craft needing 4 tungsten Alloy Ingots and an Advanced Electrical Motor made with Magnetizer magnets.
Tested safe 48V build: Held under 14 bar from 3 to 20 kW in testing. Fill the boiler with 8 buckets by hand. Place the 48V Steam Turbine one block beside the boiler with its right side against a Small Steam Condenser. Run an inverted-U iron pipe from the boiler's top port, up, one block across, and down into the turbine's top port. Mount a Pipe Safety Valve on the horizontal middle block, set to 15 bar (the test ran at 12.5 bar), outlet aimed at a wall. Put an Analogic Regulator in the turbine set to 10 bar. Put two 4-chamber Stone Heat Furnaces with their backs on the boiler's back and left flank, regulators at 230–250 °C. Pipe condensate from the condenser's front to the boiler's right-flank feed, and supply makeup water into the condenser's top from a 48V pump. Setting the valve at 12–13 bar keeps pressure below the 15 bar condenser pump rating and 230V pump shut-off, well clear of iron pipe's 20 bar working limit and 25 bar burst.
Boiler
Crafted from 5 iron ingots, a bucket, a cauldron, and a Copper Thermal Cable. Holds 8 buckets, or 8,000 mB; fill by hand with water buckets on cold start.
Heat in: Back and both side flanks, touched by furnace backs.
Feedwater in: Right flank (on your right as you face its front), behind a built-in check valve and a float that shuts at full.
Steam out: Bottom dome port directly into a turbine below, or top port via EA pipe.
Level signal: Front pin outputs 0 to 5 V from empty to full.
Failure and repair: Boiling dry burns the shell out around 420 °C. Pressure shell bursts only at 350 bar. Repair with a Copper Thermal Cable.
Steam turbines
48V Steam Turbine: Crafted from an Electrical Motor, Machine Block, 2 iron ingots, rubber, and Copper Cable. Rated 1,000 W.
Ports: Steam enters the top port only — ignore the tooltip saying any side. Electrical power leaves the front and back plates. Control signal connects on the left.
Limits and repair: Casing bursts above 25 bar, destroying the turbine in an explosion. Repair water damage with a Copper Thermal Cable.
HP Steam Turbine: Larger tier turbine rated 16 kW at 20 bar, with a casing burst at 60 bar. Steam enters through an EA pipe on its top port, and exhaust leaves out the back. Pairs at higher tiers with an LP Steam Turbine and a Plant Condenser.
Condensers
Small Steam Condenser: Crafted from EA iron and copper plates, a Machine Block, and an Electrical Motor. A larger Plant Condenser exists for HP/LP installations.
Placement: Flush against the turbine's right side (yours, facing its front). Place it from the boiler's side so its front port faces the boiler. Use a wrench to rotate the turbine if needed.
Ports: Condensate leaves the front — pipe it back to the boiler's right-flank feed. Makeup water enters the top.
Pump and cold start: The condensate return pump is driven by the turbine shaft and runs only while the turbine turns. It is rated for 15 bar and shuts off at 18 bar. Fill the boiler by hand on a cold start, and plumb the return loop before running for long — without condensate return, 8 buckets boil dry in about 5 minutes and the boiler burns out.
Makeup and flooding: The internal makeup float opens at 15% and shuts at 25%. Flooding past 50% damages the turbine. A 48V Submersible Pump feeds the top makeup port easily against condenser vacuum.
Pipe safety valve
Boilers have no built-in relief. Fit a Pipe Safety Valve, crafted from a Pipe Valve — 2 EA iron plates and a lever — plus a gold nugget and an iron nugget.
Placement: Straight stretch of pipe only, with no bend within 2 voxels. Limit one valve per block.
Setting: Right-click with an empty hand to open a slider from 1.1 to 150 bar. A fresh valve on iron pipe defaults to 10 bar.
Relief behaviour: Starts cracking open at the set point and reaches full open at +10% above set point for a steady bleed.
Scald hazard: A venting safety valve throws a jet of steam up to 1 block. A burst pipe throws steam up to 4 blocks, straight through armour. Always aim the valve outlet at a wall.
Jade fluid readouts
Jade displays steam mass in grams (g), flow in grams per second (g/s), and pressure labelled by medium, such as 10.0 bar of steam, alongside pressure efficiency relative to 10 bar open-air operation.