Early Heat and the 48V Compact Steam Turbine

Reference notes for Fire and the Kettle.

Tidied numbers for the kettle plant. Check the table before you stoke it, and check the gauges if the voltage sags or the masonry starts smelling hot.

Building the bootstrap plant

Your first ~62–220 W of 48 V power before plates, pumps, and high-pressure boilers.

Picture to come: Front isometric view of the bootstrap plant. Left block: Stone Heat Furnace with its back pressed directly to the turbine's left-side copper heat pad. Center block: 48V Compact Steam Turbine facing the viewer. Front or back terminal plate: Low Voltage Cable Kit wired straight to a Lamp Socket with no Ground Cable on the line.

  1. Craft the plant. * 48V Compact Steam Turbine: 2 copper plates of any mod's copper, 1 bucket, 4 iron ingots, 1 Electrical Motor, and 1 Copper Cable. Hand-craft the Electrical Motor from 3 iron ingots and 3 Copper Cable. * Stone Heat Furnace: 7 stone, 1 Combustion Chamber, and 1 Copper Thermal Cable. Craft a Combustion Chamber from 4 stone in a ring.
  2. Place the turbine. It faces you with its generator end toward you. The copper heat pad sits on your left as you face it.
  3. Couple the furnace. The Stone Heat Furnace gives heat only from its back. Stand facing the copper heat pad and place the furnace directly against it so its back touches the pad. These devices connect by touching, block to block; no thermal cable is needed.
  4. Add water. Right-click the turbine with Water Buckets. The tank holds 4 buckets, or 4000 mB, and takes a bucket whenever 1000 mB is free. You can also feed the top flange with an EA water pipe, whose float valve refills to 3000 mB, or with another mod's water pipe.
  5. Upgrade and regulate the furnace. Insert up to 4 Combustion Chambers into the chamber slot. Fit an On/Off Regulator crafted from redstone and iron into the regulator slot and set it to 300–400 °C so the fire throttles back if the water ever runs out. A new furnace starts on Taking fuel; feed coal or charcoal.
  6. Wire the output. Lay a Low Voltage Cable Kit from the turbine's front or back terminal plate to your loads, and switch any Lamp Socket to Cable mode in its GUI. Never put a Ground Cable on a turbine line. Unlike a battery, the turbine has no minus terminal; its output is grounded internally, so a Ground Cable shorts the rail dead.

Device numbers

Device or Parameter Value / Rating Behaviour and Failure Limits
Stone Heat Furnace 1 kW base fire, 3 kW max Only 80% of the fire heats the furnace; the rest goes up the flue. Coal or charcoal gives 200 kJ, about 1 min per coal at full 3 kW fire. Kindles in ~30 s. Its air damper follows the slider or regulator in ~5 s; the coal bed takes ~3 min to spread to a bigger fire, and with the air shut it smoulders (3 % of its bed) for ~5 min until it is down to embers. A firebox over ~350 °C lights fresh coal at once. The stone weighs ~600 J/K: about a minute from cold to 250 °C at full fire. Starts on Taking fuel; GUI button toggles Taking and Declining fuel.
Combustion Chamber +500 W fire each Max 4 chambers in the furnace for 3 kW total fire. Crafted from 4 stone in a ring. Also repairs a burned-out furnace.
Furnace Burnout 800 °C failure Burns out in place and sets fire nearby. Repair with 1 Combustion Chamber; a repaired furnace starts on Declining fuel. A bare furnace never burns out, but a furnace with even 1 chamber at full fire burns out if the turbine runs dry or is not on the heat pad.
Furnace Regulators 20–1000 °C slider Without a regulator item, the slider sets fire directly; a wet coupled turbine holds the furnace safe near 150–170 °C on bypass. With a regulator in the slot, the slider sets target temperature. Early choice: an On/Off Regulator (1 % or 10 %) from redstone and iron. An On/Off overshoots its setting by ~25 K when the load goes. The Analogic Regulator is a tuned PID that settles on the setting within a few kelvin; it needs a Cheap Chip from macerated sand, so later. Set 300–400 °C when coupled: full fire normally, throttled back if water fails. A 5 V signal on the furnace's left or right side can also set the fire externally.
Thermal Insulation Halves shell loss Crafted from 4 wool and stone. Consumes 1 insulation item whenever the furnace exceeds 520 °C.
48V Compact Steam Turbine 50.4 V max, ~62–64 W bare, ~218–220 W upgraded Converts 10% of received heat to electricity, capped at 300 W; one Stone Heat Furnace cannot reach 300 W. Power begins at 105 °C and reaches full output at 140 °C. Built-in condenser bypass opens above 150 °C up to 3.5 kW at the cost of fuel; idle sits near 155 °C. Safety valve vents water above 180 °C, unreachable on one stone furnace while wet. Grounded internally; no Ground Cable.
Turbine Water Use 4000 mB tank, 3% makeup loss Holds 4 buckets; accepts a bucket with 1000 mB free. Top flange takes EA pipes refilling to 3000 mB via float valve, or another mod's water pipes. Loses ~0.37 mB/s with 4 chambers, about 45 min per bucket loaded or idle, and ~2.4 h per bucket bare. Dry: zero power and zero heat draw. Refilling above 180 °C vents water until below 180 °C.
Lamp Socket 48 V load Defaults to wireless Lamp Supply mode; switch to Cable in the GUI when wired directly. A 48V Carbon bulb draws 25 W at 48 V and suppresses monster spawns within 9 blocks only while lit; dim, starved bulbs do not stop spawns, and Endermen and Withers ignore light.
Wind Turbine 48 V nominal, 57 V max Later tech: needs iron plates, a Machine Block, and an Electrical Motor. ~160 W at 10 m/s, 4-block tall multiblock, scales by min(y, 100)/100, needs a clear 15×5×5 air box. Cannot fail.
Water Turbine 48 V nominal, 57 V max, 30 W Later tech: needs iron plates, a Machine Block, and an Electrical Motor. Needs flowing water 1 block out and 1 block down from the front; boosts up to ~3× in local rain. Cannot fail.

Reading the gauges

What the Jade lines and meter readings mean when something goes sideways:


Reference index · Back to the contents